LPR nyomtató nevek
2004/06/21 21:46
1446 megtekintés
A cikk már legalább egy éve nem frissült, az akkor még aktuális információk lehet, hogy mára elavultak.

A Novell NetWare 4.11-től lehetőségünk van LPR alapú nyomtatásra. A legtöbb gondot általában az LPR nyomtató nevek kiderítése okozza a rossz dokumentáció, az információ hiány miatt. Cikkünkben néhány tippet, ötletet adunk a nyomtató nevek kiderítésére.

LPR nyomtató nevek... A Novell gateway képes LPR kommunkációra a nyomtatókkal TCP/IP-n keresztül. Néhány nyomtató (természetesen hálózati nyomtatókról van szó), s nyomtató szerver képes LPR alapú kommunkációra. Amikor NDPS vagy iPrint printer agent-t hozunk létre és a Novell gateway-t használjuk, akkor meg kell adnunk a nyomtató IP-címét, s nevét. Az IP-címmel semmi gond, könnyen kideríthető, ám a nyomtató LPR neve csak a nyomtató dokumentációjából, leírásából derülhet ki. A Novell gateway alapértelmezett nyomtató neve a "PASSTHROUGH". Néhány gyártó figyelmen kívül hagyja a nyomtató nevet, s függetlenül a Novell agent-ben beállított névtől elfogadja a nyomtatandó adatokat. Más gyártók csak az előre beállított névvel hajlandók nyomtatni. Az alábbi lista "néhány" hálózati nyomtató, vagy nyomtató szerver alapértelmezett nyomtató neveit tartalmazza.   Print Server Name LPR Printer Name  Axis LAN Adapters 'pr1'  Axis Office Basic 'LPT1'  Barr Systems 'BARRTCP1'  Canon GP Series Copier/Printers 'print'  Canon imageRUNNER Printers   with internal Fiery LAN Adapter  'print' or 'PRINT'  Canon imageRUNNER Printers   with imagePASS-M1 Print Controller4 'pt1' or possibly 'lpt1'  Canon imageCLASS Printers XJDIRECT  Castelle LANpress 'L1' for parallel port 1 L2' for parallel port 2  Castelle LANpress 3 'P1' for parallel port 1'P2' for parallel port 2'P3' for parallel port 3  D-Link DP300 LPT1_TEXT'   Decision Data  'd1prn  Digi Portserver Does not support LPD  Digi Portserver II 'raw_1' for parallel port 1  'raw_2' for parallel port 2  'raw_8' for parallel port 8  'raw_9' for parallel port 9  Parallel ports 10 - 16 are unknown at this time (possibly either 'raw_10 or 'raw_A' through 'raw_16' or 'raw_F').  EFI Fiery Print Server print' or 'PRINT'  Emulex PASS or TEXTCan be set to accept any value if the Emulex adapter is set to Passthru.  Epson Interface Card 'LPB''LPBF'(for formfeed after splf)  Extend Net 1005 'L1'  Extended Systems 'portLF1' or 'anydata1' for parallel port 1  'portLF2' or 'anydata3' for parallel port 2  'portLF3' or 'anydata3' for parallel port 3  If 'portLF1', 'portLF2' or 'portLF3' causes a blank page before and after each spooled file, try using 'anydata1', 'anydata2' or 'anydata3' instead.  GENICOM 5000 series   with PS1000 series NIC 'PASSTHRU  GENICOM 5000 series   with EasyCom Express NIC 'LPDPRT1  GENICOM 5000 Series   With Emulex PS1000   Network Interface Card (Internal) 'GENICOM' (all uppercase)  GENICOM Printers   with Microplex M205, M206 or M305 NIC  'd1prn'  GENICOM Printers   with Microplex M202 or M202+   external print server  d1prn1' for parallel port 1  'd2prn2' for parallel port 2  'd3com1' for serial port 1  'd4com2' for serial port 2  GENICOM Printers   with Printronix PrintNet 'd1prn'  GENICOM Printers with MPS100 MPS_nnnnnn_P1' where "nnnnnn" represents the last six digits of the MAC address  Hawking Tech Print Server 'PS_Port-1' or 'LP1'  Hitachi DDS 32/40 Printers 'pcl5  Hitachi DDS 50/62 Printers   (with internal Fiery LAN Adapter)  'print' or 'PRINT'  HP JetDirect Card (Internal) 'raw' (formatted output)  'text' (unformatted text)  Note:  The formatting will insert a LF CR to unformatted text.  PCL and Postscript print jobs should be sent unformatted  HP JetDirect Server  (Single-Port External) 'raw' (formatted output)  'text' (unformatted text)  Note:  The formatting will insert a LF CR to unformatted text.  PCL and Postscript print jobs should be sent as raw.  HP JetDirect Server   (External) (Same IP address used for all three ports)  'raw1' for parallel port 1 (formatted output)  'text1' for parallel port 1 (unformatted text)  'raw2' for parallel port 2 (formatted output)  'text2' for parallel port 2 (unformatted text)  'raw3' for parallel port 3 (formatted output)  'text3' for parallel port 3 (unformatted text) Note: Any name sent through, such as PASSTHROUGH, will default to parallel port 1. The formatting will insert a LF CR to unformatted text.PCL and Postscript print jobs should be sent as raw.  HP Wireless Print Server   (External) 'raw' (formatted output)  'text' (unformatted text)  Note:The formatting will insert a LF CR to unformatted text. PCL and Postscript print jobs should be sent as raw.  IBM 3130 'afccu2  IBM 6400 Network Connection   (Internal)  'd1prn' for single port  IBM 6400 Network Connection   (External)  'pr1' for parallel port 1  'pr2' for parallel port 2  'pr8' for parallel port 8  IBM OS/400 (R310 or Above to   R310 or Above) output queue name (for example. 'PRT01')output queue library / output queue name (for example, 'QUSRSYS/PRT01')*USER*SYSTEM  IBM OS/400 (R310 or   Above to R230) *USERuser ID (for example, 'QSECOFR'  IBM Infoprint 20 (4320)  IBM Infoprint 32 (4332)  IBM Infoprint 40 (4340)  IBM Infoprint 70 (2770) 'PASS' (formatted output)  'TEXT' (unformatted text)  IBM Infoprint 60 (3160)  IBM Infoprint 62 (4370) 'afccu2'  IBM Integrated Network Option (IBM 4039, 4049, 3112, 3116) same as Lexmark MarkNet XL (Internal)'/prt0'  IBM Network Print Server   (NPS) 'pr1' for parallel port 1  'pr2' for parallel port 2  'pr3' for parallel port 3  IBM Network Printer 12, 17 or 24  (IBM 4312, 4317 or 4324) 'PASS' (formatted output)  'TEXT' (unformatted text) Note: 'TEXT' appears to work best for the IBM Network Printer 20  IBM Network Station 'PARALLEL1' for the parallel port  'SERIAL1' for the serial port  IBM RS/6000   (Printer Attached to RS/6000 System) printer queue name (case sensitive)  i-Data EasyCom, PlusCom,   LinkCom Printservers LPDPRT1 or LPDPRT2  Intel Netport XL 'TEXT1' for parallel port 1  'TEXT2' for parallel port 2  'PASSTHRU' to disable blank page  Intel Netport Pro 'LPTx_PASSTHRU' (formatted output  'LPTx_TEXT' (unformatted text) where x = port  (The PASSTHRU options will disable banner or trailer pages)  Intel NetportExpress XL and Pro 'LPT1_PASSTHRU' for parallel port 1 (formatted output)  'LPT1_TEXT' for parallel port 1 (text)  'LPT2_PASSTHRU' for parallel port 2 (formatted output)  'LPT2_TEXT' for parallel port 2 (text)  'PASSTHRU' for serial port (formatted output)  'TEXT' for serial port (text)  'COM1_PASSTHRU' for serial port if 'PASSTHRU' does not work.  (The PASSTHRU options will disable banner or trailer pages)  Intermec Printers (Internal)  'pr1'  JETNet Card 'PASS'  Konica (Internal) 'lptprt1'  Lantronix Print Servers 'DSS_TEXT' for single parallel port (unformatted text)  'EPS_nnnnnn_P1' for parallel port 1  'EPS_nnnnnn_P2' for parallel port 2  where "nnnnnn" represents the alpha-numeric name stamped on the device. Note: This is the default value for the Lantronix print server, but it can be changed by telnetting to the print server.  Lantronix LPS 'LPS_nnnnnn_TEXT' for simple ASCII text or dot matrix printers.  'LPS_nnnnnn_PCL' for HP LaserJet compatible printers  'LPS_nnnnnn_PS' for PostScript printers  where 'nnnnnn' represents the alpha-numeric name stamped on the printer server. Note: This is the default value for the Lantronix print server, but it can be changed by telnetting to the print server.  Lantronix MPS1-T and MPS1-2 'MPS_nnnnnn_TEXT' for text and Zebra bar code printers (unformatted text)  'MPS_nnnnnn_PCL' for HP LaserJet and compatible printers (formatted output)  where "nnnnnn" represents the alpha-numeric name stamped on the device. Note: This is the default value for the Lantronix print server, but it can be changed by telnetting to the print server.  Lexmark MarkNet XL   (Internal) '/prt0'  Lexmark MarkNet XLe   (External)   Lexmark MarkNet Pro   (External) '/prt1' for parallel port 1  '/prt2' for parallel port 2  '/prt8' for parallel port 8  '/prt9' or '/ser' for serial port  Lexmark MarkNet Pro3   (External)   Lexmark MarkNet 2000 (External) '/prt0' or '/par0' for parallel port 1  '/prt1' or '/par1' for parallel port 2  '/prt9' or '/ser' for serial port  LINKSYS Pocket Print Server L1  Mannesman-Tally PR2  Microplex M205   (Internal)  Microplex M206   (Internal)  'd1prn'  Microplex M202   (External)   Microplex M202+   (External)  'd1prn1' for parallel port 1  'd2prn2' for parallel port 2  'd3com1' for serial port 1  'd4com2' for serial port 2  Minolta Di6200 Print Server  'print' or 'PRINT'  Minolta PageWorks 25 'PORT1_PASTHRU'  MINOLTA-QMS   CrownNet Print Servers 'raw'  Mita 'LPAF'  Netgear 'L1'  Net Print   (Internal)  'PORT1'  Océ printers  (with external Fiery LAN Adapter)  print' or 'PRINT'  Océ 3155/3165 Digital Copier Printer queue name configured through OS/2 Warp on attached Dell PC (case sensitive)  Osi.com JetXPrint   (Internal) 'PORT1'  Osicom NetPrint   (External) 'PORT1' for parallel port 1  'PORT2' for parallel port 2  Printronix PrintNet 'd1prn' for single port  'd1prn' for parallel port 1  'd2prn' for parallel port 2  'd3prn' for parallel port 3  'd4prn' for parallel port 4  Ricoh Aficio Printers  'PORT1'  Ricoh EB70, EB105, EB105E Printers 'print'  Sato Printers *NONE Note: Presumably, Sato printers with internal Sato print servers will work with any RMTPRTQ value.  Savin Printers  'PORT1'  Sharp Printers  'PORT1'  StarTech Print Servers 'lpt1' for parallel port 1  'lpt2' for parallel port 2  'lpt3' for parallel port 3  Tektronics Phaser 550 Printer 'PS', 'HPGL', 'PCL', or 'AUTO'  The PCL or AUTO should work in most cases.  Toshiba DC Printers 'raw'  Typhoon 'pcl5'  Unisys WinPath 3000 Series Terminals  Printer name (case sensitive) specified in the LPD Config on the terminal  Unix (Printer Attached to Unix System) Printer queue name (case sensitive)  Windows 95, Windows 98 and Windows ME LPD queue name (case sensitive)  Windows NT and Windows 2000 Printer share name (case sensitive)  WYSE 3000 Series Terminals printer name (case sensitive) specified in the LPD Config on the terminal.  XCD 'BINARY_P1' for parallel port 1 (formatted output)  'TEXT_P1' for parallel port 1 (unformatted text)  'BINARY_P2' for parallel port 2 (formatted output)  'TEXT_P2' for parallel port 2 (unformatted text)  'BINARY_S1' for serial port 1 (formatted output)  'TEXT_S1' for serial port 1 (unformatted text)  Xerox 4517 'PASSTHRU'  Xerox DC230 Printer 'lp'  Xerox N40 'lp'  Xerox 6200 DN Phaser Printer type needs to be Generic PS  'print_6200'  See Xerox Document  Zebra Printers with ZebraNet Print Server   (MPS1-T and MPS1-2)  'MPS_nnnnnn_TEXT' for text and Zebra bar code printers (unformatted text)  'MPS_nnnnnn_PCL' for HP LaserJet and compatible printers (formatted output)  where "nnnnnn" represents the alpha-numeric name stamped on the device.  Note: This is the default value for the ZebraNet print server; however, it can be changed by telnetting to the print server.  Zebra Printers   with ZebraNet Print Server II  'portLF1' for parallel port 1  'portLF2' for parallel port 2  'portLF3' for parallel port 3  Molnár Péter

Csatlakozz hozzánk!

Ajánljuk

European Schoolnet Academy Ingyenes online tanfolyamok tanároknak
School Education Gateway Ingyenes tanfolyamok és sok más tanárok számára
ENABLE pilot Program iskoláknak a bullying ellen
eBiztonság Minősítés Minősítési rendszer oktatási intézményeknek